Roof square footage calculator
Works out the area of a gable or shed roof, in square feet and roofing squares, and how many sheets of sheathing it takes.
Your roof is about 1,221 sq ft. Order 13.5 squares of shingles.
- Area1,221 sq ft
- Squares before waste12.2
- With 10% waste13.5 squares
- Sheathing sheets (4 x 8, before waste)39
For a simple gable or shed roof. Work out dormers, wings and porches as separate roofs and add them.
Show the working
- Footprint with overhang. Each side grows by the overhang: (40 ft + 2 ft) × (24 ft + 2 ft) = 1,092 sq ft.
- Pitch multiplier: √(12² + 6²) ÷ 12 = 1.118.
- Roof area: 1,092 × 1.118 = 1,221 sq ft, rounded to the nearest square foot.
- Squares: 1,221 ÷ 100 = 12.2, rounded to the nearest tenth.
- Waste: 12.2 × 1.10 = 13.43, rounded up to 13.5 squares. We round up to the next tenth so you don't come up short.
- Sheathing: a 4 x 8 sheet covers 32 sq ft. 1,221 ÷ 32 = 38.2, rounded up to 39 sheets.
Every figure is worked from the unrounded area, so the rounding never builds up. We assume the same pitch on both sides, an overhang on all four sides and no extra roofs. How we calculate
How the area is worked out
A sloped roof is bigger than the footprint under it. So we start with the footprint, including the overhang, and multiply it by a number that depends only on the pitch. A flat roof would have a multiplier of 1. The steeper the roof, the bigger the multiplier.
For 6 in 12 the multiplier is 1.118: every square foot of footprint becomes about 1.12 square feet of roof. It is the same slope factor the rafter calculator uses.
What a roofing square is
A roofing square is 100 square feet of roof. Shingles, felt and underlayment are sold by the square, so a 1,221 sq ft roof is 12.2 squares. We then add a little for waste: cut-offs at the edges and ridge, and the odd damaged shingle.
A worked example
A garage 40 ft long and 24 ft wide, with a 6 in 12 roof and a 12 in overhang on every side. The footprint with overhang is 42 ft by 26 ft, which is 1,092 sq ft. Times 1.118, the roof is 1,221 sq ft, or 12.2 squares. Add 10% for waste and round up: 13.5 squares. Plywood sheets for the deck: 1,221 ÷ 32 is 38.2, so 39 sheets.
Common questions
Does this work for a hip roof?
Roughly. The area of a hip roof is about the same as a gable roof over the same footprint, but there are more cuts, so pick 15% for waste. Check the result against your own measurements.
Do I measure the overhang along the slope?
No. Measure it level, from the outside of the wall to the tip of the roof edge, like a plumb line dropped from the edge. The calculator adds the slope for you.
How much waste should I allow?
We use 10% for a simple gable roof and 15% for a roof with hips or valleys. These are our own rules of thumb, not a rule from a manufacturer. Ask your supplier if you want a different figure.
What about dormers, a porch or a second wing?
Work each one out as its own roof and add the areas together. This page assumes one rectangle with the same pitch on both sides.
Related
Last reviewed 18 November 2026 · How we calculate · Report a wrong answer